Controll-A-Door S series Bedienerhandbuch

www.bnd.com.auN1854B&D Doors is a division of B&D Australia Pty Ltd ABN 25 010 473 971 Controll-A-Door® P DiamondInstruction ManualSectional

C-Rail AssemblyStep 1 - Attach C-Rail to PowerheadLocate and insert the powerhead’s shaft into the C-Rail’s sprocket as shown in (Fig. 05).Step 2 - Se

Fig. 09Fig. 08Fig. 07Determine the Door TypeStep 3 - Determine the Door TypeDetermine which type of garage door you have as illustrated in (Fig. 07) t

TrackDoorTrackLevelLevelDoorDrilled holesStructural memberFig. 13Fig. 12Fig. 11Fig. 10Mounting on a Track Type DoorStep 4 - Determine Bracket Position

Centre of doorStep LadderStep LadderC railDoorHighest point of door travelFig. 16Fig. 15Fig. 14Fig. 17Mounting on a Non-Track Type DoorWARNING: Make s

ACeilingAluminium railShuttle assemblyDrill hole at centre of track (recommended bolt size M6 or M8)The height of bolt head must not exceed 6 mm Fig.

Setting Speed and LimitsStep 14 - Setting Speed ModeThe default speed of the opener has been set to suit the majority of applications. However, there

Setting Travel Limits IMPORTANT NOTE: The OPERATE button will not function until the open and close limit positions are set. NOTE: The door and shuttl

Testing Safety Obstruction ForceCAUTION: Take care when testing the safety obstruction force. Failure to follow this warning can result in serious per

Coding TransmittersPress CODE SET button onceSelect one of the four buttons you wish to use to control the doorPress CODE SET button twiceSelect one o

Press CODE SET button three times Select one of the four buttons (not programmed yet ) you wish to use to control the Auxiliary out putPress CODE SET

Safety Rules 03Risk Assessment 04Default Settings & Specifi cations 05About Your Opener 06Operating Controls 07Kit Contents 09Inst

Press CODE SET button fi ve times Select one of the four buttons (not programmed yet ) you wish to use to control the door for pet positionFig. 32Fig.

Step 20.1 -Wireless Photo Electric (PE) Beams (optional)A photo electric (PE) Beams extends across the door opening. This Safety Beam is designed to d

Step 20.3 -Connecting The Base Station To The Openera. Connect WHITE wire from base station to 0V on the terminal block of the openerb. Connect RED

Step 20.5 -Fixing The Base Station To Wall/OpenerThe base station can be attached directly to a sectional opener using the M8 bolt and nut supplied. T

Fig. 35Fig. 36REDBLACKREDBLACKREDBLACKBLACKWired Safety Beams InstallationStep 19 - Safety Beams (optional)Safety Beams extend across the garage door

Fig. 47AccessoriesTerminal BlockA variety of wired accessory items can be connected to the terminal block such as Safety Beams, electric key switch,

Battery Back Up InstallationBattery Back Up (optional)The opener has provision for a Battery Back Up kit that allows continued operation of the door i

Fig. 49How to use your openerFor maximum effi ciency of your opener, your garage door must be in good operating condition.An annual service of your gar

Fig. 50REPLACE BATTERY WITH CR2032 ONLYHow To Use Your OpenerRemoving the Battery From the Transmitter(Battery Type: 3V Lithium Battery CR2032). Use a

How To Use Your OpenerSafety BeamA Safety Beam Kit (Part No 062734) may be fi tted to this opener. • When this option is fi tted, the operation of this

Safety RulesPlease read these important safety rulesThese safety alert symbols indicate a personal safety or property damage instruction exists. READ

MaintenanceMaintenanceWhilst your opener does not require any periodic maintenance, the door that it is fi tted to, does. Your garage door is a large,

If You Need a Service CallIf the opener needs service please call the dealer who installed the garage door opener (for product assistance contact 13 6

ParametersDoor status indicatorsDoor opener state OPEN LED (green) CLOSE LED (red) BeeperOpen OnClose OnOpening FlashingClosing FlashingDoor travel st

Spare Parts ListDiamond PD Power Drive : Instruction Manual© Copyright 2012 B&D Doors33Controll-A-Door® P Diamond SDO-2v2 Instruction Manual

WarrantyProduct: CAD P Purchased from:______________________________Purchaser:___________________________________

Warranty(b) instructions - failure to observe any instructions or directions (including “warning” notifi cations in the Instruction Manual), provided

Optional AccessoriesThere is a range of additional accessories for your added convenience and security.• Safety Beams - Part No 062734. Gives additio

www.bnd.com.auQLD Offi ce: 17 Oasis Court, Clontarf 4019. Ph: (07) 3883 0200NSW Offi ce: 34-36 Marigold St, Revesby 2212. Ph: (02) 9722 5555VIC/T

Please refer to the risk assessment table below and ensure all the necessary controls are in place.Installation Risk AssessmentHazard ControlMuscular

Default Settings & Specifi cationsFactory default settingsDefault Step Minimum MaximumMaximum opener run time 60 seconds - - -Courtesy light time 4

Thank you for choosing a Controll-A-Door® P Diamond automatic garage door opener, designed and developed in Australia by B&D Doors.The technically

Operating Controls01. Terminal Block. V+ is used to power devices such as Wireless Safety Beam, external receiver etc. EB1 input is used to connect

02Fig. 0104010708091005061112131403Controll-A-Door® P Diamond SDO-2v2 Instruction Manual8

Kit ContentsPowerhead Unit (Fig. 02)1 x Controll-A-Door® P Diamond powerhead1 x Transmitter pack (Pack includes two keyring transmitters and batterie